Menu
Hi bernabyp,you patch works as well, but problem is that different Arduinos have different IDs.I still think, there is a bug in eggbot-extension, because in eggbot.py calls function 'getSerialPort'which first calls eggbotscan.findEiBotBoards. If that does not find anything (which is right, because we do not have an Eggbotboard with proper USB-ID), it is supposed to execute function eggbotscan.findPorts.
If the issue does not persist in safe mode, then perform clean boot and check whether the issue resolves. Safe mode starts Windows with a limited set of files and drivers. Startup programs do not run in safe mode, and only the basic drivers needed to start Windows are installed. I am setting up a new Eggbot but I am seeing a 'Failed to connect to EggBot.:(' error whenever I try to apply anything in the Inkscape Eggbot Controller. I am able to see the Eggbot controller board in my windows device drivers and control.
Which looks for any devices on serialports.Problem is, that if findEiBotBoards does not find anything, findPorts is not esecuted. I do not really understand why, but that is the problem. If we comment out that block with findEiBotBoards, everything works like expected.Yogi. Hello,i tried to run your arduino-software with inkscape today, but it didn't work. EggBotControl Release 2.5.0 date 2015-01-30. your actual firmware.
I tried your patch and also the patch with the VID/PID of my arduino. arduino nanoThe arduino is working, because I get the answer 'EBBv13andabove Protocol emulated by Eggduino-Firmware V1.4'The Inscape Script is connecting my board (led flashing), but get a wrong answer, so it stops.' Unable to find an Eggbot on any serial port.:(Error reading serial data.' Hello everybody. I want to make eggbot but I almost suffered a mental breakdown.
I'm trying for three days and does not work. The first problem is when I try to install EggDuino returns an error.
On the Internet I found the solution that you have to replace that void inline inline void. Then it was loaded onto an Arduino. If i type anything in serial console it won't answer anything.
In inkscape I get message: Unable to find an Eggbot on any serial port.:(I searched the entire Internet and tried everything possible but no luck.I was try:andbut without any luck. I gave up over all.I have Arduino nano clone with CH340. On Fri, Feb 10, 2017 at 11:49 AM, duezero.@. wrote:No changes on Inkscape. Reset pin must stay always connected to 5V using aresistor, 10k is good (pull up). But shall be disconnected from the resetsignal (which drives rst pin to ground triggering the reset) once youuploaded the program. You shouId try with a standalone MCU (or maybe cutphysically the signal on your NANO but I'm not shure because I dont have aNANO)—You are receiving this because you commented.Reply to this email directly, view it on GitHub,or mute the thread.
I feel like I had this same problem.I'll look through pictures and see if I can find anything useful-James-On Fri, Feb 10, 2017 at 11:49 AM, [email protected]: No changes on Inkscape. Reset pin must stay always connected to 5V using a resistor, 10k is good (pull up). But shall be disconnected from the reset signal (which drives rst pin to ground triggering the reset) once you uploaded the program. You shouId try with a standalone MCU (or maybe cut physically the signal on your NANO but I'm not shure because I dont have a NANO) — You are receiving this because you commented.
Reply to this email directly, view it on GitHub, or mute the thread. On Fri, Feb 10, 2017 at 1:25 PM, bosko90.@. wrote:I didn't find that. But I tray:alternatively, you can replace 'EBBport = None' with your specific portnumber:EBBport = 'COMxx' #WindowsEBBport = '/dev/ttysomething' #Linux/Macchange to 'COM4' and it's wooooooork!
Servo is moving. Now Imust connect the stepping motors. Hope it is work.
Yura80 thanx! And ofcourse thanks to all of you I offer assistance. Now it is 8 hours behindme. If I need anything I write tomorrow.—You are receiving this because you commented.Reply to this email directly, view it on GitHub,or mute the thread.
Hello to you all,I'm new to GitHub and joined to talk with you about my issue. I tried everything you posted before and i also tried versions of Eggduino. With the newest IDE 1.8. I can't get his sketch to run through my compiler. It get stuck everytime by this Part and I dont know how to fix it.' HelperFunctions:4: error: 'SELFPRGEN' was not declared in this scopeSPMCSR &= SELFPRGEN;exit status 1'SELFPRGEN' was not declared in this scope'Do you have any clue what I should change to your Sketch to get it running?Funfact aside: I tried 'Ejjduino' the Eggbot Version from jjrobot and it worked fine on my ArduinoMEGA. I could also connect it to Eggbot Inkscape extension, after some modifications.
But it failed to move. Duezero posted this last time:Try this oneOrOther than that, try older versions of IDEOn Feb 22, 2017 4:47 PM, 'Asenom' wrote:Hello to you all,I'm new to GitHub and joined to talk with you about my issue. I triedeverything you posted before and i also tried versions of Eggduino. With the newest IDE 1.8.I can't get his sketch to run through my compiler. It get stuck everytimeby this Part and I dont know how to fix it.' HelperFunctions:4: error: 'SELFPRGEN' was not declared in this scopeSPMCSR &= SELFPRGEN;exit status 1'SELFPRGEN' was not declared in this scope'Do you have any clue what I should change to your Sketch to get it running?Funfact aside: I tried 'Ejjduino' the Eggbot Version from jjrobot and itworked fine on my ArduinoMEGA. I could also connect it to Eggbot Inkscapeextension, after some modifications.
But it failed to move.—You are receiving this because you commented.Reply to this email directly, view it on GitHub,or mute the thread. On Feb 23, 2017 3:54 PM, 'Asenom'.@. wrote:Thank you very much! I tried it and it seems to work with all the otherchanges!
I also tried to connect with the Inkscape extensions and bychecking for the EBB Version it also replied with the right Version. Ithink the communication is now properly working! I will give a reply on howit worked with steppers and the servo motors, but first i have to changethe PINs!Thank you very much!:)—You are receiving this because you commented.Reply to this email directly, view it on GitHub,or mute the thread.
On Sun, Mar 5, 2017 at 1:11 AM, duezero.@. wrote:Different topic, is there any way I could run the Gcode while it's in theArduino code? My plan is to push a button, draw an egg, push a button, drawan egg, etc.I think you should re-design the whole firmware.
Actually the programreads commands sent by Inkscape extension that are NOT g-code. Conversionfrom 'drawing-G-code-eggbot commands' is performed by inkscape extension—You are receiving this because you commented.Reply to this email directly, view it on GitHub,or mute the thread.